Warmup Binding

This binding integrates the Warmup 4iE Thermostat https://www.warmup.co.uk/thermostats/smart/4ie-underfloor-heating (opens new window), via the API at https://my.warmup.com/ (opens new window).

Any Warmup 4iE device(s) must be registered at https://my.warmup.com/ (opens new window) prior to usage.

This API is not known to be documented publicly. The binding api implementation has been derived from the implementations at https://github.com/alyc100/SmartThingsPublic/blob/master/devicetypes/alyc100/warmup-4ie.src/warmup-4ie.groovy (opens new window) and https://github.com/alex-0103/warmup4IE/blob/master/warmup4ie/warmup4ie.py (opens new window), and enhanced by inspecting the GraphQL endpoint.

Supported Things

The Warmup binding supports the following thing types:

Bridge	Label	Description
my-warmup	My Warmup Account	The account credentials for my.warmup.com (opens new window) which acts as an API to the Warmup device(s)

Thing	Label	Description
room	Room	A room containing an individual Warmup 4iE device which is a WiFi connected device which controls a heating circuit.

Room

The device is optimised for controlling underfloor heating (electric or hydronic), although it can also control central heating circuits. The device reports the temperature from one of two thermostats, either a floor temperature probe or the air temperature at the device. The separate temperatures do not appear to be reported through the API. It appears to be possible to configure two devices in a primary / secondary configuration, but it is not clear how this might be represented by the API and hasn't been implemented.

Discovery

Once credentials are successfully added to the bridge, any rooms (devices) detected will be added as things to the inbox.

Thing Configuration

My Warmup Account

config parameter	type	description	required	default
username	String	Username for my.warmup.com (opens new window)	true
password	String	Password for my.warmup.com (opens new window)	true
refreshInterval	Integer	Interval in seconds between automatic refreshes	true	300

Room

Rooms are configured automatically with a Serial Number on discovery, or can be added manually using the "Device Number" from the device, excluding the last 3 characters. The only supported temperature change is an override, through a default duration configured on the thing. This defaults to 60 minutes.

config parameter	type	description	required	default
serialNumber	String	Device Serial Number, excluding last 3 characters	true
overrideDuration	Integer	Duration in minutes of override when target temperature is changed	true	60

Channels

channel	type	description	read only
currentTemperature	Number:Temperature	Currently reported temperature	true
targetTemperature	Number:Temperature	Target temperature	false
overrideRemaining	Number:Time	Duration remaining of the configured override	true
runMode	String	Current operating mode of the thermostat, options listed below	true
frostProtectionMode	Switch	Toggles between the "Frost Protection" run mode and the previously configured "active" run mode (known options are either Fixed or Schedule)	false

Run Mode Statuses

These run mode statuses are defined for the API. The descriptions are based on inspection of the device behaviour and are not sourced from documentation.

api value	ui name	description
not_set	Not Set	Unknown
off	Off	Device turned off
schedule	Schedule	Device target temperature running to a programmed schedule
override	Override	Target temperature overridden for the remaining duration in overrideRemaining
fixed	Fixed	Device target temperature set to a constant fixed value
anti_frost	Frost Protection	Device target temperature set to 7°C
holiday	Holiday	Device target temperature set to a constant fixed value for duration of holiday
fil_pilote	Fil Pilote	Unknown
gradual	Gradual	Unknown
relay	Relay	Unknown
previous	Previous	Unknown

Full Example

.things file

Bridge warmup:my-warmup:MyWarmup [ username="[email protected]", password="test", refreshInterval=300 ]
{
    room    bathroom    "Home - Bathroom"   [ serialNumber="AABBCCDDEEFF", overrideDuration=60 ]
}

.items file

Number:Temperature bathroom_temperature "Temperature [%.1f °C]" <temperature> (GF_Bathroom, Temperature)    ["Temperature"] {channel="warmup:room:MyWarmup:bathroom:currentTemperature"}
Number:Temperature bathroom_setpoint    "Set Point [%.1f °C]" <temperature> (GF_Bathroom) ["Set Point"] {channel="warmup:room:MyWarmup:bathroom:targetTemperature"}
Number:Time bathroom_overrideRemaining  "Override Remaining [%d minutes]" (GF_Bathroom) {channel="warmup:room:MyWarmup:bathroom:overrideRemaining"}
String bathroom_runMode "Run Mode [%s]" (GF_Bathroom) {channel="warmup:room:MyWarmup:bathroom:runMode"}
Switch bathroom_frostProtection "Frost Protection Mode" (GF_Bathroom) {channel="warmup:room:MyWarmup:bathroom:frostProtectionMode"}

Sitemap

Text label="Bathroom" {
    Text item=bathroom_temperature
    Setpoint item=bathroom_setpoint step=0.5
    Text item=bathroom_overrideRemaining
    Text item=bathroom_runMode
    Switch item=bathroom_frostProtection
}

Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)